Centurion D5/D3 Gate Motor Basic Info. D.I.Y- more videos on chenturion on my channel


hello from blade @ Blade productions
the interduction is all about the centurion d5 and d3 pc boards
the basics of the centurion pc board will now be shown
call outs of technicians can run from R 550 to R 850 for the first 15 min…
now we start at the d5 microchip
you can see 3 x fuses 2 x relays for motor to open and close
all explained is just the basic connections on the pcb
ok if your motor is not working you should start by checking your battery and charging
check the date on the battery check the motor fuse as shown
this is the pc board fuse check the AC power on the motor
check the red light on the transformer under the motor
do not mix fuses and stick to the factory fitted sizes
please check this space for future programming on the centurion motors
thank you blade

24 thoughts on “Centurion D5/D3 Gate Motor Basic Info. D.I.Y- more videos on chenturion on my channel

  1. Now I know which fuse is which, thank you…. it would have been very valuable if you mention the fuse ratings I need to buy to replace them.

  2. GOOD DAY.
    could any one pls help as I have a D3 motor but it does not want to move.i have replaced the batt,stil nothing.i also have removed all power from the motor still dead. but there is the trick part the status led flashes 4 times.pls help
    0825646458
    martin

  3. hi, are you online? Im having trouble connecting the receiver to the pcb board of the d3?

  4. Hello Blade
    Thanks for the valuable info on the Centurion gate motor systems.
    I have had a look at the 5 videos and I will now see if I I can get my gate going again.
    Thanks again and keep streaming.

  5. hi Blade, Elijah here. Mind if I call you for assistance with my d5 motor, it's closed ams won't open.

  6. Hi Blade, thank you very much for this video. I hear the click-click-click sound, and following your advice I checked the fuse near the relays. I will replace it now. Please keep posting new videos, I appreciate them!

  7. Hi Blade, dankie vir die fliek! i think the motor fuse has blown, what type of fuse must replace it with?

  8. Hi Blade. Do you have any videos on programming an E.T. Blu remote to the Centurion D5 motor. I had a new E.T. garage motor installed recently and now want to use the same remote for my motor gate, instead of two different remotes.

  9. hwzt I have a problem with my motor led on da pc board is on lock can I reset it or overide it please help

  10. Hi blade I want to connect my intercom so that I will open gate from inside. My intercom is commax 7" video

  11. plz can Simone tell we have a et500 slidinding gate motor but on the panel there was a loose orange wire on circuit board where does it go contact no 0217030222 thanx alot

  12. Hi Blade, thank you for DIY session. I'm have challenge, I have to get close to the gate for the remote to open the gate, how do extend the range of my remote? Please help

  13. What do i do if the test button and the relays is not working?

  14. Hi Blade,thanks for the informative videos!I have a problem on my centurion d5-v1 motor-When I press my remote to open the gate,I get one beep only from the pcb,I tested the battery and got 13v,and the fuses are all working-Any advice or help will be much appreciated.

  15. Hi Mark, I have install D5 EVO 3 years ago . but now my gate won 't open . on the motor screen it says battery low and is connected to my main switch. if the problem is with the battery can u advice me on how to replace it. Thank u

  16. GOOD EVEN THANK YOU TO HELP ME THE GATE ENGINE BOARD SHOWS THE FOLLOWING PROBLEM

    WHEN I TURN ON THE COMMAND SHE TURNS OFF THE LIGHTS

    AND DO NOT OPEN THE DOOR MOTOR D5 CENTURION

  17. The mosfet on my board failed.
    What is the part number for the mosfet?
    Kind regards

Leave a Reply

Your email address will not be published. Required fields are marked *